Skip to content

Shelly 2PM Gen4

← README · All devices · Commands

State: untested Generation: 4 Chip: ESP32-C6

🧰 Before you start · ⚙️ Config · ⚡ Flash it · 👀 What to expect · ↩️ Way back

Gen4 / ESP32-C6.

Fact Value
Profile S2PMG4
Flash 8 MB
Official package 2.1.0
Partition table 0x10000
App slot size 0x300000
ESPHome device page Shelly Plus 2PM Gen 4

Before you start

Check first:

  • the device runs Shelly's own firmware, not ESPHome yet
  • you know its IP address (--ip), or this PC is on the device's own access point (default 192.168.33.1)
  • the device can reach this PC: same network, port 8000 (--port) not blocked
  • your ESPHome config uses the partition table below and is compiled
  • a UART adapter is at hand as your way back (Recovery over UART)

ESPHome config

Important

build refuses a config without Shelly's partition table. Copy partitions/S2PMG4-stock.csv from this repository next to your YAML and keep CONFIG_PARTITION_TABLE_OFFSET: "0x10000".

esp32:
  variant: ESP32C6
  board: esp32-c6-devkitc-1
  flash_size: 8MB
  partitions: S2PMG4-stock.csv        # copy from partitions/ in this repository
  framework:
    type: esp-idf
    sdkconfig_options:
      CONFIG_PARTITION_TABLE_OFFSET: "0x10000"
    advanced:
      enable_ota_rollback: false

ota:
  - platform: esphome
    allow_partition_access: true

The C6 needs the 80 MHz flash header, otherwise build refuses to replace the bootloader. If it complains, add under esphome::

esphome:
  platformio_options:
    board_build.flash_mode: dio
    board_build.f_flash: 80000000L
    board_build.flash_size: 8MB

Tip

The ESPHome device page has a config to start from. Replace its esp32: block with the one above, or build refuses it.

Flash it

  1. Install the requirements (once):
pip install -r requirements.txt
  1. Fetch the official package:
python ota.py fetch S2PMG4 --insecure
  1. Build: put your app into it; the ZIP goes to out/:
python ota.py build S2PMG4 app.ota.bin --esphome-factory app.factory.bin --esphome-yaml app.yaml
  1. Check the device first. Nothing is sent:
python ota.py send S2PMG4 out/S2PMG4-app-<date>.zip --ip <device IP> --dry-run
  1. Flash it and watch the log:
python ota.py send S2PMG4 out/S2PMG4-app-<date>.zip --ip <device IP> --watch 120

app.ota.bin and app.factory.bin are the two files ESPHome compiles. --dry-run only checks the device and, for this package, reads the update target slot. Command reference: Commands.

What to expect

In the --watch log look for these lines, in this order:

# Log line Meaning
1 Update target slot: 0 ... The slot check of send. Anything else: run python ota.py restore S2PMG4 first
2 Boot: cur ... min ... update? 1 The installer will write ESPHome's bootloader. update? 0 means it will not: build again with a higher --boot-min-version (why)
3 ota_progress up to 95 %, then ota_success The device restarts into ESPHome

Notes for this device

No device-specific findings yet. Please report the --watch log, especially the lines Update target slot, Boot: cur ... update? and Will write to slot.

The profile sets boot_min_version: "1.0.9": devices of this family run Shelly's loader 1.0.3, which would otherwise skip ESPHome's bootloader (update? 0).

A Tasmota template exists on templates.blakadder.com. Its note: the temperature sensor needs AdcParam1 2,10000,10000,3350 for accurate values.

Way back

python ota.py restore S2PMG4 sends the official firmware back while Shelly firmware still runs.

Warning

  • Wipes Wi-Fi and settings. ESPHome opens its own access point or joins the Wi-Fi from your config; if nothing comes up, power-cycle the device (help).
  • No way back over the network once ESPHome's bootloader runs: restore gets no answer, only UART brings Shelly OS back (Recovery over UART). Take a flash backup first if you can.
  • Flashed it? Tell us, also when it worked: open a device report.

Bootloader and slots · Troubleshooting · Recovery over UART